Tracert command syntax
traceroute to www.szabist.edu.pk (202.5.152.253), 30 hops max, 40 byte packets
1 192.168.1.232 (192.168.1.232) 0.182 ms 0.101 ms 0.098 ms
2 192.168.1.230 (192.168.1.230) 2.102 ms 2.528 ms 2.929 ms
3 125-209-118-57.multi.net.pk (125.209.118.57) 13.562 ms 14.200 ms 14.608 ms
4 mppl-ip-gw-03.multi.net.pk (202.141.224.7) 896.946 ms 897.816 ms 898.824 ms
5 khi77.pie.net.pk (202.125.134.169) 899.480 ms 899.822 ms 900.532 ms
6 202.125.159.109 (202.125.159.109) 900.869 ms 571.306 ms 572.009 ms
7 khi77.pie.net.pk (202.125.128.136) 572.313 ms 540.538 ms 541.754 ms
8 szabist.khi77d1.pie.net.pk (202.125.131.38) 542.646 ms 543.570 ms 544.455 ms
9 202.5.152.253 (202.5.152.253) 545.099 ms 545.750 ms 546.060 ms
(No Ratings Yet)
Loading ...About the Author
Adam has written 384 stories on this site.
Related Tutorials & Articles
Network connectivity between source and destination not limited to two hosts, it can be more than two hosts. Ping command just show the status whether source can reach destination or not but in case of tracert it check each intermediate hope between source host and destination hop. It’s better to know where the problem in...Read more
eth0 Link encap:Ethernet HWaddr 00:06:5B:5D:20:39 inet addr:192.168.1.31 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::206:5bff:fe5d:2039/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14746 errors:0 dropped:0 overruns:1 frame:0 TX packets:4469 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6262829 (5.9 MB) TX bytes:468170 (457.1 KB) Interrupt:18 Base address:0xcc00 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:168 errors:0 dropped:0 overruns:0 frame:0 TX packets:168 errors:0...Read more
WATM (Wireless Asynchronous Transmission Mode) experience burst errors, which needs flexible error control scheme. There are two types of basic error schemes ARQ(Automatic Error Request) send NACK (Negative Acknowledgment) for retransmission of packets when it is lost and cannot be recovered, second type id FEC (Forward Error Correction) transmits redundant bits with original data to ...Read more
1. What are two reasons that a network administrator would use access lists? (Choose two.) A: to control vty access into a router B: to control broadcast traffic through a router C: to filter traffic as it passes through a router D: to filter traffic that originates from the router E: to replace passwords as a line of defense against...Read more
PING 125.209.115.81 (125.209.115.81) 56(84) bytes of data. 64 bytes from 125.209.115.81: icmp_seq=1 ttl=253 time=2.10 ms 64 bytes from 125.209.115.81: icmp_seq=2 ttl=253 time=1.04 ms 64 bytes from 125.209.115.81: icmp_seq=3 ttl=253 time=1.09 ms 64 bytes from 125.209.115.81: icmp_seq=4 ttl=253 time=1.16 ms 64 bytes from 125.209.115.81: icmp_seq=5 ttl=253 time=1.04 ms 64 bytes from 125.209.115.81: icmp_seq=6 ttl=253 time=1.14 ms 64 bytes from 125.209.115.81: icmp_seq=7 ttl=253 time=1.19...Read more
One Comment on “Tracert command syntax”
Trackbacks
Write a Comment
Gravatars are small images that can show your personality. You can get your gravatar for free today!
